Looking for:
Rth6360d1002 manual |
Rth6360d1002 manual.5-2 Day Programmable Thermostat With Backlight
Then press Select to save changes and advance to the next System Setup number. Repeat until all of the System Setup options have been set. The thermostat will automatically save and exit to the Home screen. Maximum of 2 Cool stages or 1 Compressor stage. Quick Installation Guide System operation settings 1 Press the Mode button to cycle to the next available System mode. RTH Series Program Schedule You can program four time periods each day, with different settings for weekdays and weekends.
Wake - Set to the time you wake up and the temperature you want during the morning, until you leave for the day. Away - Set to the time you leave home and the temperature you want while you are away usually an energy-saving level. The new setpoint temperature will be held until the next scheduled time period begins. RTH Series Wiring—heat pump Connect wires: heat pump 1 2 Match each labeled wire with same letter on new thermostat.
Insert the wires into the matching terminal. NOTE: If you have difficulty inserting wires, you may have to press down the terminal push button next to the corresponding terminal. If labels do not match letters on thermostat, see page Press Select to save and exit. You will see the year blinking. RTH Series 3 When the alert icon appears, check the error code with the table below to determine the problem. Please replace the thermostat. Quick Installation Guide Troubleshooting If you have difficulty with your thermostat, please try the following suggestions.
Most problems can be corrected quickly and easily. Display is blank Make sure fresh AA alkaline batteries are properly installed see page 6. Cannot change system setting to Cool Check System Setup Option to make sure the options are set to either 1 or 2 see page 9.
RTH Series 1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one 1 year from the date of purchase by the consumer. Disconnect power before beginning installation. Contact your local waste management authority for instructions regarding recycling and proper disposal.
Veuillez remplacer le thermostat. With automatic changeover from heat to cool and short cycle protection, this programmable thermostat is easy to install and set up. New technology aside, this thermostat delivers on those must-have features you want. The large, backlit display shows current and set point temperatures, a real-time clock and your choice between Fahrenheit or Celsius. Reminders for filter changes and low batteries are two less things to worry about.
The install and the programming were very easy to do. As such I am pleased with this product and would recommend it. This is the new version of what I had installed years ago.
I think it is a little more user friendly but it is programmed different. Glad I bought it. Confusing directions for a split system that operates individually of each other. Fixed the wiring and all seems good. Was very easy to install. Needed help with one wire and customer service was a big help. Easy to read and use display, smart response feature. Honeywell RTHD Day Programmable Thermostat Easily schedule the thermostat so that your system will meet your temperature and comfort needs for the week, or for weekdays and weekends.
Classic Features New technology aside, this thermostat delivers on those must-have features you want.
Honeywell RTHD/E Programmable Thermostat, Schedule : User Guide.User Manual Honeywell RTH6360D1002/E Thermostat
Table Of Contents. Available languages. Quick Links. Table of Contents. Previous Page. Next Page. Switch Breaker box Check that your system is off. Change the temperature on your old thermostat to be above room temperature in heat mode or below Be sure to include the letters next to the terminals where the wires are inserted. This will be a helpful reference when wiring your thermostat. Tip: If the color of your wires has faded or if 2 terminals have the same wire color, use the wire labels provided in the package to label Find an authorized professional near you to complete your installation.
Skip to main content. Our Accessibility Statement. Best Seller. Requires a pro for pricing, installation and warranty Toggle This product is sold exclusively through our Professional Partners. This product is temporarily out of stock.
Volume Discount Pricing is a great way for customers to save big on large, bulk orders of most items available in our store.
Please send a bulk order request to our friendly sales staff so they may create a quote and provide personal service for your order! You will receive a response within business days and our office hours are Monday through Friday, 8am-5pm CST. Get a detailed quote from a dedicated sales rep.
Our warehouse ships directly to you. Send A Request Now. Please confirm wiring matches terminals from the photo you took in Step 5.
Mount the UWP using the provided screws. Installall three screws for a secure fit on your wall. Close the door after you're finished. Insert two AA alkaline batteries in the back of the thermostat as shown. Press Select. Then press Select to save changes and advance to the next System Setup number. Repeat until all of the System Setup options have been set. The thermostat will automatically save and exit to the Home screen. Press Select to save and exit. You can program four time periods each day, with different settings for weekdays and weekends.
We recommend the pre-set settings shown in the table below. ON is displayed. Press Select to keep the schedule period on. Time starts blinking. Temperature starts blinking. Press Home when you're finished to save program settings and return to the home screen. The new setpoint temperature will be held until the next scheduled time period begins. If you must connect both R and Re wires. If your old thermostat had only 1 C or C1 wire, connect it to the C terminal.
If your old thermostat had 2 C or C1 wires, wrap each separately with electrical tape and do not connect them. C does not power the thermostat display or operations; batteries are always required. NOTE: If you have difficulty inserting wires, you may have to press down the terminal push button next to the corresponding terminal.
If your old thermostat had both V and VR wires, stop now and contact a qualified contractor for help. If your old thermostat had separate O and B wires, attach the B wire to the C terminal.
If another wire is attached to the C terminal, stop now and contact a qualified contractor for help. If this is desired, please contact a contractor for replacement model.
Press Select to save changes and advance to the next System Setup number. Batteries are required to provide power. Install fresh batteries immediately when the low battery icon appears.
The icon appears about two months before the batteries are depleted. Even if the low battery icon does not appear, you should replace batteries once a year, or before leaving home for more thana month. If batteries are inserted within two minutes, the time and day will not have to be reset. All other settings are permanently stored in memory, and do not require battery power. Press Menu to enter the device menu. F for Fahrenheit and C for Celsius.
You will see the alert icon on the home screen. Insert the wires into the matching terminal. NOTE: If you have difficulty inserting wires, you may have to press down the terminal push button next to the corresponding terminal.
If labels do not match letters on thermostat, see page Press Select to save and exit. You will see the year blinking. RTH Series 3 When the alert icon appears, check the error code with the table below to determine the problem. Please replace the thermostat. Quick Installation Guide Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.
Display is blank Make sure fresh AA alkaline batteries are properly installed see page 6.
Rth6360d1002 manual.Honeywell Home RTH6360D1002 Quick Installation Manual
The Honeywell Day Programmable Thermostat features an easy to read backlit display that will allow for instant accessibility at a glance. Hold settings will allow you to modify programming as needed. Your programming is retained in the thermostat's memory even if there's a power outage. With automatic changeover from heat to cool and short cycle protection, this programmable thermostat is easy to install and set up. New technology aside, this thermostat delivers on those must-have features you want.
The large, backlit display shows current and set point temperatures, a real-time clock and your choice between Fahrenheit or Celsius. Away - Set to the time you leave home and the temperature you want while you are away usually an energy-saving level. The new setpoint temperature will be held until the next scheduled time period begins. RTH Series Wiring—heat pump Connect wires: heat pump 1 2 Match each labeled wire with same letter on new thermostat. Insert the wires into the matching terminal.
NOTE: If you have difficulty inserting wires, you may have to press down the terminal push button next to the corresponding terminal.
If labels do not match letters on thermostat, see page Press Select to save and exit. You will see the year blinking. RTH Series 3 When the alert icon appears, check the error code with the table below to determine the problem. Please replace the thermostat. You will see F or C displayed. F for Fahrenheit and C for Celsius.
You will see the alert icon on the home screen. Once viewed the home screen will maintain the alert symbol until it is cleared. Snoozed alerts will appear 7 days after dismissing them in the alerts menu screen. When the alert icon appears, check the error code with the table below to determine the problem.
If you have difficulty with your thermostat, please try the following suggestions. Heat pump issues cool air in heat mode, or warm air in cool mode. Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one 1 year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions,. Golden Valley, MN , or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Can cause electrical shock or equipment damage. Disconnect power before beginning installation. If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash.
Contact your local waste management authority for instructions regarding recycling and proper disposal. It should not be disposed of with other household waste. Use manuals file type: PDF. Honeywell - Thermometers. Home Bookmarks Brands Reviews About us. Documents : Go to donwload! Works With. Get Started. Compare Products. Related Products. Similar Products. Product Overview. To adjust program schedules Press Menu on your thermostat.
Then ON is displayed. Repeat steps 4 through 7 for the remaining schedule periods. Wiring - conventional systems Alternate wiring conventional systems If labels do not match terminals, connect wires as shown below see notes, below.
NOTES: 1. Wiring - heat pump Connect wires: heat pump 1 Match each labeled wire with same letter on new thermostat. If labels do not match letters on thermostat, see page Keep R Slider Tab in the up position 1 wire. Auxiliary heat must wire to AUX or E. Advanced menu 1. Press Select to cycle through System Setup numbers. To save and exit early, press Home to return to the Home screen. Battery replacement Batteries are required to provide power. NOTE: When replacing batteries, alkaline batteries are recommended.
Setting the time 1. Set the date 1. You will see the year blinking. Setting degrees Fahrenheit F or Celsius C 1. You will see F or C displayed. Alerts screen 1. Snooze the alert. Dismiss the alert. Alerts codes - Internal Memory Error: The memory of the thermostat has encountered an error. Please replace the thermostat - Thermostat Temperature Sensor Error: The sensor of the thermostat has encountered an error. Please replace the thermostat. Reset the timer by touching the "dismiss" button on thermostat screen after it is replaced.
Replace them within two months. Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Display is blank Make sure fresh AA alkaline batteries are properly installed see page 6 Cannot change system setting to Cool Check System Setup Option to make sure the options are set to either 1 or 2 see page 9 Fan does not turn on when heat is required Check System Setup Option to make sure it is set to match your heating equipment see page 8.
Heating system is running in cool mode Check System Setup Option or to make sure it is set to match your heating and cooling equipment see pages 8 and 9. Heating or cooling system does not respond Press System to set system to Heat. Make sure the temperature is set lower than the Inside temperature Check circuit breaker and reset if necessary. Heat pump issues cool air in heat mode, or warm air in cool mode Check System Setup Option or to make sure it is set to match your heating and cooling equipment see pages 8 and 9.
Pull to remove the thermostat from the UWP. Honeywell Customer Care toll-free at Specs Sheet. Download User Manual.
No comments:
Post a Comment